HTA 90/22 Aluminum Barrel Shroud For Factory 10/22 Barrels

Price: $59.99

Milspec hard coat anodized aluminum barrel shroud with Melonite treated threaded adapter for factory Ruger 10/22 barrels.

Part Number: HTABSWA

Availability: Out of Stock.

Description
Customer Reviews

Sometimes polymer just isn't good enough, especially if you're a die-hard shooting enthusiast. It is for these purists in the community that we developed an aluminum alternative to our 90/22 polymer barrel shroud. This shroud features rugged, hardcoat anodized aluminum construction and is designed to fit 18.5" Ruger 10/22 tapered barrels with front post sights (removed) when installed in our bullpup rifle stock. The 1/2-28 threads necessary to attach the shroud are provided by the included nitride treated thread adapter which locks onto the muzzle with two set screws and a spring pin. Made in the USA and backed by HTA's lifetime warranty.

Note: This product requires the factory front post sight be removed from the barrel prior to installation. Depending on the customer's experience and equipment, a gunsmith may be recommended.
CA Proposition 65 Warning

Warning: The included adapter may be illegal in some jurisdictions by creating a threaded attachment point for muzzle devices. Know your local laws.

Warning: Do not attempt to use the included adapter with a baffled muzzle device such as a muzzle break or suppressor as this could result in a bullet strike on the device.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and reproductive harm. For more information, go to https://www.P65Warnings.ca.gov

Rating Snapshot

Select a row below to filter reviews.

Average Customer Ratings

4.4

View All Reviews - Reset

Needed lots of hand fitting

I had high hopes for this kit, as it appears to greatly enhance the look and feel of the 90/22 stock kit (over the standard plastic shroud). However, out of the bag from the factory, it was obvious that the adapter would not easily fit over the factory 10/22 front sight band. I had to remove a fair amount of metal from the inside of the adapter to finally make it fit. Even then, it's fair to say that it is now a permanent installation, as the adapter is so tight it may never come off. In the end, I still like the look and feel, but the adapter tolerances should be a bit more open to make installation easier. [ HTA Response: Hello Eric and thank you for your business! Very sorry there was an issue with the fitment of the adapter. We were recently made aware of some changes Ruger has seemingly made with their barrel tolerances. We have offered this product for several years without issue, but in the past few weeks, we have been hearing similar stories. We are in the process of remaking the adapters with looser tolerances based on customer input and data on the size of their front sight post. All adapters sold after 1/1/2022 will be the updated design, reflecting changes we've seen made by Ruger. If you have any issues with the fitment of any of our products, always feel free to contact us and we will do whatever we can to remedy the issue from our end. Thank you for your business and feedback!]

Did you find this helpful? 13 of 13 Found Helpful

Reviewed by: Eric Barnes from Tennessee on 12/26/2021

Do it!

the fake suppressor that comes standard makes the whole stock just feel/look off (too big and plastic) just go with out it... OR... UPGRADE TO THE ALUMINUM ONE!!!!! It makes the whole setup! its smaller in diameter and securely attached. it makes for a very realistic appearance. just make sure the set screws are tightened enough to clear the side of the adapter, really small clearances and it will catch if you don't have it all the way in.

Did you find this helpful? 6 of 7 Found Helpful

Reviewed by: (Verified Buyer) Daniel Lutz from GOOSE CREEK, SC United States on 9/6/2016

Makes the device 100x better looking

Front sight was a bit hard to get out but once you get it out it’s pretty much straight forward. Install was simple. Aluminum shroud makes it look 100x better and more authentic (compared to my real PS90). Thank you Andy + HTA for the great products!

Did you find this helpful? 4 of 4 Found Helpful

Reviewed by: (Verified Buyer) Jorelle Pagdilao from Hawaii on 9/27/2022

SWEET

Oh man...lol. I have to bother you one more time about this shroud. SWEET is all I can say. What a difference. I'm a bit of a purist(?). The difference in this and the plastic one is just great!!! I love it man, thanks again for a great company with great products and great customer service.

Did you find this helpful? 3 of 3 Found Helpful

Reviewed by: (Verified Buyer) HAPPY CAMPER from Elizabethtown, Tennessee on 8/11/2020

Really Nice

This Greatly enhances the look of the 90/22 stock it feels great and looks fantastic well worth the money!

Did you find this helpful? 3 of 3 Found Helpful

Reviewed by: (Verified Buyer) Norris from on 7/15/2020

HTA 10/22 Bolt Buffer

$3.99

Usually Ships in 24 Hours

(1)

Select Options

HTA 10/22 Magazine Coupler

~~$10.99 Original price~~ $9.99 Sale

In Stock.

(10)

Add To Cart

HTA RM-25 Windowed 10/22 Magazine

~~$29.99 Original price~~ $24.99 Sale

Usually Ships in 24 Hours

(7)

Select Options

High Tower Armory 90/22 (Arctic Gray)

$269.99

Usually Ships in 24 Hours

(5)

Add To Cart

HTA 90/22 Aluminum Side Rail with QD Sling Pocket

$16.99

Usually Ships in 24 Hours

(0)

Select Options

High Tower Armory 90/22 (Black)

$269.99

Usually Ships in 24 Hours

(66)

Add To Cart

High Tower Armory 90/22 (Flat Dark Earth)

$269.99

Usually Ships in 24 Hours

(11)

Add To Cart

High Tower Armory 90/22 (OD Green)

$269.99

Usually Ships in 24 Hours

(26)

Add To Cart

High Tower Armory 90/22 (Desert Tan)

$269.99

Usually Ships in 24 Hours

(16)

Add To Cart

HTA 90/22 Aluminum Barrel Shroud For Factory 10/22 Barrels

Related Items